steve-m.de wiki

This page is read only. You can view the source, but not change it. Ask your administrator if you think this is wrong.
====== Driving the Motorola F3 e-paper display ======

The Motorola F3/MOTOFONE was the first (and still is the only?) mobile phone with an e-paper display. Although this is not a pixel-based display, like found in eBook-readers (e.g. the Amazon Kindle or the B&N nook), it is still quite nice for experimenting with low power microcontroller projects.

E-paper/bistable displays have the ability to sustain the display content even without the supply of power, so initial idea I had was to build something like a clock, only powering the display when updating it every minute.

===== The display=====
The display consists of 182 individually drivable segments, which form a row of six 14-segment characters, a row of six 8-segment characters, and many symbols used for user notification and the menu.

|{{:display_segments.jpg?350|PCB with segments of the display}}|{{:display_all_on.jpg?341|assembled display showing all segments}}|
|The PCB of the display|Display showing all segments|

===== Display controller =====
As you can see from [[http://www.eetindia.co.in/ARTICLES/2007SEP/C/EEIOL_2007SEP17_EMS_NETD_TA.gif|this picture]], the used display controller is a [[http://www.solomon-systech.com/products/ssd1621.htm|Solomon Systech SSD1621]]. Unfortunately there is no public datasheet, so I had to sniff the (32 bit) SPI communication between the TI Locosto baseband processor and the display. The protocol turned out not to be very difficult, just some initialization, some commands for actually writing the display content, and a command to refresh the display with the just transmitted content.\\
The most time has been spent for actually finding out which bit was for which segment, since all segments are wired up at random to the segment outputs of the controller. This is not surprising though, given that you need a circuit path to each and every segment - "just get them wired already, we can handle the rest in software" seemed to be the motto :-)

===== Interfacing with the display =====
Normally, the baseband board and the display/keypad pcb are connected with a 32-pin connector (exact model unknown). Luckily there are pull-up resistors and capacitors for every needed signal, so I decided to solder some wires there, instead of directly to the connector. The schematics of this phone are floating around the web (just search for **f3_schem.rar**).

|{{:f3_wires_soldered.jpg?350|thin wires soldered to the display pcb}}|{{:f3_display_connector.jpg?436|the connector of the display}}|

This is the pinout of the connector, signals that were used are highlighted:

|**pin**|**signal**||**pin**|**signal**|
|01|SPKPA||02|TEMP_SENSOR|
|03|SPKNA||04|**DISPLAY_BUSY1**|
|05|HS_SPK_CHARGE||06|HSMIC_OUT|
|07|GND||08|VLED|
|09|HSSPK_CHG_N||10|LED_C|
|11|GND||12|**DISPLAY_32K**|
|13|DISPLAY_BUSY0||14|**SYS_RESET**|
|15|**SPI_nCS0**||16|**SPI_CLK**|
|17|**SPI_MOSI**||18|SPI_MISO|
|19|**VIO**||20|**VBAT**|
|21|PWON||22|KBR(0)|
|23|KBR(1)||24|KBR(2)|
|25|KBR(3)||26|KBC(0)|
|27|KBC(1)||28|KBC(2)|
|29|KBC(3)||30|KBC(4)|
|31|GND||32|PCHGAC|
|33|RF_ANT||34|GND|

===== Microcontroller =====
To drive the display, I'm using a TI MSP430G2231 low-power microcontroller on the TI Launchpad. The Launchpad has been populated with the external 32KHz crystal oscillator that comes with it.
The connection between display and Launchpad is as follows:

|**MSP430**||**display**||
|port|signal|pin|signal|
|P1.0|ACLK 32KHz clock output|12|DISPLAY_32K|
|P1.1|display supply|19+20|VIO+VBAT|
|P1.2|busy input|04|DISPLAY_BUSY1|
|P1.3|display reset|14|SYS_RESET|
|P1.4|SPI slave-select|15|SPI_nCS0|
|P1.5|SPI clock|16|SPI_CLK|
|P1.6|SPI MOSI|17|SPI_MOSI|

{{:msp430_epaper.jpg?300|Launchpad with connected display}}
===== Sourcecode =====
The sourcecode can be found on github:
[[https://github.com/steve-m/epaperclock|]], and can be cloned with

  git clone git://github.com/steve-m/epaperclock.git

~~DISCUSSION~~
steve-m.de wiki

User Tools

Site Tools

Page Tools
